Accuracy problems.....
#1
Fork Horn
Thread Starter
Join Date: Aug 2006
Location: Bushton, KS
Posts: 136
Accuracy problems.....
I am very accurate under 30 yrds, but when I get back to 40 or 50 I am all over the place. I think it is my fletching. I have just straight 3.5" fletching. If I went to the blazers will this help? And why? Thanks
#3
Join Date: Feb 2007
Posts: 2
RE: Accuracy problems.....
If you think it's fletching contact spray your rest and riser with atletes foot, tenactin or any type of powder and then shoot your bow and look for lines. what type of rest are you using?? make sure if it's a drop away that it rises up the last 1-1/2" to 2" prior to full draw. I've seen several shooters rest tied off wrong and they start rising at the onset of the draw making it virrtually a fixed rest.
#4
Fork Horn
Thread Starter
Join Date: Aug 2006
Location: Bushton, KS
Posts: 136
RE: Accuracy problems.....
It is a trophy taker shaky. I think it is because with my straight vanes the arrow does not spin. I read once that for longer shots you should use fletching that makes the arrow spin. Is this true?
#5
RE: Accuracy problems.....
somewhat especially with broadheads...use an offset 4 inch fletch...you will no its offset buy looking at how the vane is glued on the shaft. it will be at a 2-4 degree angle instead of parralell to the edge of the shaft...
another fletch is called helical wich gives even more spin....when looking down the shaft you will notice the vane is not only offset but appears twisted(curved) around the shaft ....i cant comment on blazers...i dont use them...i use 4 inch helical feathers and as big an offset as i can get for hunting...slows the arrow down some but it doesnt matter at 20 yards.
an example of this causing spin, would be a table top fan...when you blow at it the fan blade spins.....because of more resistance on one side of the blade than the other(offset) a strait vane has equal resistance on both sides so it doesnt spin
another fletch is called helical wich gives even more spin....when looking down the shaft you will notice the vane is not only offset but appears twisted(curved) around the shaft ....i cant comment on blazers...i dont use them...i use 4 inch helical feathers and as big an offset as i can get for hunting...slows the arrow down some but it doesnt matter at 20 yards.
an example of this causing spin, would be a table top fan...when you blow at it the fan blade spins.....because of more resistance on one side of the blade than the other(offset) a strait vane has equal resistance on both sides so it doesnt spin
#6
RE: Accuracy problems.....
ORIGINAL: gibsonhoyt
I am very accurate under 30 yrds, but when I get back to 40 or 50 I am all over the place. I think it is my fletching. I have just straight 3.5" fletching. If I went to the blazers will this help? And why? Thanks
I am very accurate under 30 yrds, but when I get back to 40 or 50 I am all over the place. I think it is my fletching. I have just straight 3.5" fletching. If I went to the blazers will this help? And why? Thanks
#7
Fork Horn
Thread Starter
Join Date: Aug 2006
Location: Bushton, KS
Posts: 136
RE: Accuracy problems.....
The problem is with both broadheads and field tips. I shoot Carbon Excell 400's 29" length 4.1gpi 100g tip. Standard vanes.Bow is set at 70#30"Hoyt Vextrix XL. I also shoot fingers. I shot yesterday and at 30 yrds I was fine but back to 40 and 50 I was all over.
Thanks for the help on this!
Thanks for the help on this!
#8
Join Date: Jan 2007
Posts: 40
RE: Accuracy problems.....
If you're getting good arrow flight and are grouping well at 30 yards, I doubt your problem is with your arrows. I suspect it has more to do with anchor point/peep location.
As distances increase - especially out at 40, 50 60, etc. your anchor point is going to change slightly since your peep sight is raising slightly with the increase in elevation of your bow. Granted, we're talking very, very small changes, but those small changes are magnified as distance increases.
A slight cant of the bow, which may only be reflected as a right/left shift in point-of-impact at 20 yards of 1/2" could result in a change of 3" or more at 60 yards. A small change of anchor point at 60 yards, will result in the same type of inconsistency.
Field archers, who regularly shoot at 70, 80, and 90 yards, are constantly battling these types of problems
As distances increase - especially out at 40, 50 60, etc. your anchor point is going to change slightly since your peep sight is raising slightly with the increase in elevation of your bow. Granted, we're talking very, very small changes, but those small changes are magnified as distance increases.
A slight cant of the bow, which may only be reflected as a right/left shift in point-of-impact at 20 yards of 1/2" could result in a change of 3" or more at 60 yards. A small change of anchor point at 60 yards, will result in the same type of inconsistency.
Field archers, who regularly shoot at 70, 80, and 90 yards, are constantly battling these types of problems
#9
RE: Accuracy problems.....
Several things I would suspect...First, you are close to being underspined....In fact, you are. That could be part of it. Another part of the equation is simply this.....The farther away you are from your target the more difficult it is to hit, and groups open up. Third, you may have a tuning issue....but to be honest, sitting here there is NO WAY I could tell you for sure.
I will say this......Last summer I was practicing for season, and was shooting Magnus Stingers w/ Blazers from 70 yards....I was consistently hitting a 2" square w/ that combo....Do Blazers work, you better believe it.
I will say this......Last summer I was practicing for season, and was shooting Magnus Stingers w/ Blazers from 70 yards....I was consistently hitting a 2" square w/ that combo....Do Blazers work, you better believe it.