Bent lower axle on a Trykon?
#1
Bent lower axle on a Trykon?
Well, I was looking over my bow this evening and spotted something.
I was concerned that it could be a bent axle shaft on the lower cam but I wanted to see if any Trykon owners would spot the same thing.
Look over your lower cam. Is it completely vertical when you look at it from your shooting angle (just like you would hold the bow to shoot) or is it a little tweaked (the top of the cam is a little farther left than the bottom part of the cam) It is a very slight angle, but when I look at it, it is definately noticable.
I am concerned it may be a axle that is bent if you guys don't see the same thing I am seeing.
Hopefully you guys can give me some feedback.
Thanks
I was concerned that it could be a bent axle shaft on the lower cam but I wanted to see if any Trykon owners would spot the same thing.
Look over your lower cam. Is it completely vertical when you look at it from your shooting angle (just like you would hold the bow to shoot) or is it a little tweaked (the top of the cam is a little farther left than the bottom part of the cam) It is a very slight angle, but when I look at it, it is definately noticable.
I am concerned it may be a axle that is bent if you guys don't see the same thing I am seeing.
Hopefully you guys can give me some feedback.
Thanks
#3
RE: Bent lower axle on a Trykon?
Thanks for the reply. I am glad you have noticed the same thing. Makes me feel better.
I never did get a good look at the cams and how they weresituated betweens thelimbs before I started shooting it.
I just figured most cams were basically vertical. Hopefully this is normal for the Trykons and it doesn't show signs of a bent axle or something.
Anyone else notice this on the Trykons?
I never did get a good look at the cams and how they weresituated betweens thelimbs before I started shooting it.
I just figured most cams were basically vertical. Hopefully this is normal for the Trykons and it doesn't show signs of a bent axle or something.
Anyone else notice this on the Trykons?
#4
Join Date: Mar 2005
Location:
Posts: 174
RE: Bent lower axle on a Trykon?
You will probably notice serving wear on your cable because of this cam lean.
If you do: You can fix it by getting an adjustable cable guard rod, using a cable slide that doesnt deflect the cables as much. Or by replacing the fuse cables with a thinner serving diameter aftermarket set of cables.
This problem isnt uncommon on the new Trykons, so just keep an eye out for that serving wear.
Have a good one---Matt
If you do: You can fix it by getting an adjustable cable guard rod, using a cable slide that doesnt deflect the cables as much. Or by replacing the fuse cables with a thinner serving diameter aftermarket set of cables.
This problem isnt uncommon on the new Trykons, so just keep an eye out for that serving wear.
Have a good one---Matt
#5
Join Date: Jan 2006
Location: Middletown, Pa.
Posts: 95
RE: Bent lower axle on a Trykon?
It's not only on the Trykons but most single cam or cam+1/2 systems. Basically it is caused by limb torque due to the cable rod/slide. It's very common but not what I'd call normal or desireable. Without a solid yoke cable there is nothing you can do about it either. Ya need to read "Letter #5" on Spott Hogg's website to learn more about this---commonly referred to as Cam-Lean.
Just another reason I went back to a two cam bow.
Just another reason I went back to a two cam bow.
#6
RE: Bent lower axle on a Trykon?
anything with a cable rod, obviously one side of the limbs are getting pulled harder and the shorter the ata the higher the angle.
i was looking at that fuse string and it looked like they used crown serving or something. it was pretty fat, and on the demo bow i saw the cable was getting ate up.
i was looking at that fuse string and it looked like they used crown serving or something. it was pretty fat, and on the demo bow i saw the cable was getting ate up.
#7
RE: Bent lower axle on a Trykon?
Thanks a bunch guys. Like I have said a lot of times here on these forums, it is nice to have a place to bring your questions. This sport is more complex than people give it credit at times. And it is even more complex and confusing when you first start out. So I appreciate the help.
So I can lessen this phenomena (as I like to call it) by either switching to a new cable guard that doesn't pull those cables so far to the right to clear the bowstring, or deal with the cable guard but purchase a new set of cables and strings with a smaller serving diameter to eliminate the wear and tear from the angle of the cam.
Am I reading your guy's post right?
How are the FUSE strings? Are they pretty tough or will I be looking to replace the strings before 2 years or so?
So I can lessen this phenomena (as I like to call it) by either switching to a new cable guard that doesn't pull those cables so far to the right to clear the bowstring, or deal with the cable guard but purchase a new set of cables and strings with a smaller serving diameter to eliminate the wear and tear from the angle of the cam.
Am I reading your guy's post right?
How are the FUSE strings? Are they pretty tough or will I be looking to replace the strings before 2 years or so?
#8
RE: Bent lower axle on a Trykon?
bols, just as an update, i'm starting to get lots of inquiries about building string sets for these bows in hopes some of this issue can be solved.some folks are reporting already having gone through 2 cables of the type that came on the bow. i don't have any idea if its an issue with the cable itself, the serving, or the lean you're talking about.