Limb twist!!?? Please help.
09-06-2006, 08:42 AM
#1
Fork Horn
Thread Starter
Join Date: Feb 2006
Location: Houston, Tx
Posts: 457
Limb twist!!?? Please help.
The weather cooled off consideraby yesterday so I spent about 2 hrs outside shooting yesterday evening. I came inside to check the string, serving and cables.(they're pretty old and frayed so I wax them everytime I shoot... hopefully they'll make it through this year.) Iwas looking at the Cam(Single cam on a Martin Phantom Mag) and noticed that the cam is not entirely parallel to the string and bus cable. Causing some serving wear on the string and cable. Upon further inspection, the cam itself is actually getting frayed from the string, especially on the draw module(which abhorrently enough is plastic).
I'm guessing that shooting it like this is asking for a blow up.
What are the causes for this and is there anything I can do to alleiviate it?
I'm guessing that shooting it like this is asking for a blow up.
What are the causes for this and is there anything I can do to alleiviate it?
09-06-2006, 10:02 AM
#4
Join Date: Aug 2005
Location: Massachusetts
Posts: 842
RE: Limb twist!!?? Please help.
It could just be cam lean. Might need to twist the cables on one side.
What bow are you shooting that has plastic modules on the cam? Are you sure that it's not just a coating? Many these days have teflon or some other sort of coating on the cams and modules, which is likely what you are seeing being frayed.
What bow are you shooting that has plastic modules on the cam? Are you sure that it's not just a coating? Many these days have teflon or some other sort of coating on the cams and modules, which is likely what you are seeing being frayed.
09-06-2006, 10:10 AM
#5
Dominant Buck
Join Date: Feb 2003
Location: land of the Lilliputians, In the state of insanity
Posts: 26,274
RE: Limb twist!!?? Please help.
How is the cam time? Did you mark it when it was shooting right? If you have a press, check the axil. If it is limb twist, replace it. I would not shoot it in that condition. Not only will you cause more problems, but is also dangerouse. Id check everything. Tiller, timeing, cam/wheel spacers, limb pocket, etc. etc...
09-06-2006, 01:42 PM
#6
Fork Horn
Thread Starter
Join Date: Feb 2006
Location: Houston, Tx
Posts: 457
RE: Limb twist!!?? Please help.
mannnn.... i was hoping someone would say "nah, it'll be fine..." [&:]I'll take it to a shop and see what they say. I really don't have any more money to put into this thing.
Yeah, plastic modules. I'm pretty sure its not just a coating. the serving is chewing into the cable channel pretty good... I mentioned to the shop guy I'd expected them to be aluminum at least. He just kinda scoffed and said... "on a martin?"
Tiller is good. Smack dab the same. It is the distance from limb to string measured at the point the limb meets the riser right? I never thought to check the timing. I didn't think it was vital with a singlecam. If it is off, ist not by much. Limb pockets are both clear. I checked before bottoming out the limbs.
This really chaps my @$$!!! [:@]
Chalk it up to alearning experience I suppose......
Yeah, plastic modules. I'm pretty sure its not just a coating. the serving is chewing into the cable channel pretty good... I mentioned to the shop guy I'd expected them to be aluminum at least. He just kinda scoffed and said... "on a martin?"
Tiller is good. Smack dab the same. It is the distance from limb to string measured at the point the limb meets the riser right? I never thought to check the timing. I didn't think it was vital with a singlecam. If it is off, ist not by much. Limb pockets are both clear. I checked before bottoming out the limbs.
This really chaps my @$$!!! [:@]
Chalk it up to alearning experience I suppose......
