Clearance Sale Omega
#1
Nontypical Buck
Thread Starter
Join Date: Aug 2008
Location: Rapid City, South Dakota
Posts: 3,732
Clearance Sale Omega
This rifle i purchased because it was reduced for clearance, and had a wood stock. At the time i had no use for it, but the wood stock made the purchase necessary. Recently i realized i needed this rifle, because an X7 was ruined. The day before yesterday a scope was mounted, and yesterday i took it up and kinda zeroed the scope. This morning the target was first located at 200 yard, and 2 shots taken from the clean cold barrel. The load was 110g BH, 300g Deep Curl, crush rib sabot, W209 primer.
It seemed prudent to photograph the target, so i walked about 500 yard to and from the target. Temperature was 54*, and it was a nice walk, even wearing shorts and t-shirt.
The rings are quick release so for to exchange scopes easily. For muzzy season the scope will need to be 1X. Four more shots were taken. The first shot was a way right, but fourth, and fifth were in the black. Six i wanted to be in the black, but no. When finished here the temperature was 53*
The 200 yard shooting was satisfactory, so i drove about 4 mile away, and set up a 300 yard target. By this time a breeze had begun. It seemed kinda foolish to try 300 yard shooting because of the breeze, and because the bullets would have slowed to near the speed of sound, but i gave it a try. Well, well, the wind pushed the bullet far enough over so it hit the steel frame of the target holder, and knocked the whole shebang over.
Photos show the bullet after hitting steel @ 300 yard.
Then i drove back to where i had been shooting before, and shot twice at 100 yard.
A move was made to 200 yard, and 3 shots taken. The breeze was left to right.
When the rifle was cleaned for the initial shooting a couple day ago, i didn't replace the new breech plug. The new plug was exchanged with one that had worn at both ends. The worn flash hole was replaced with a stainless vent liner, and the flame cut primer seat was cut deeper, and now an o-ring is used.
The last photo shows the rifle with a 1X scope just now mounted. And now you know what the next task will be.
It seemed prudent to photograph the target, so i walked about 500 yard to and from the target. Temperature was 54*, and it was a nice walk, even wearing shorts and t-shirt.
The rings are quick release so for to exchange scopes easily. For muzzy season the scope will need to be 1X. Four more shots were taken. The first shot was a way right, but fourth, and fifth were in the black. Six i wanted to be in the black, but no. When finished here the temperature was 53*
The 200 yard shooting was satisfactory, so i drove about 4 mile away, and set up a 300 yard target. By this time a breeze had begun. It seemed kinda foolish to try 300 yard shooting because of the breeze, and because the bullets would have slowed to near the speed of sound, but i gave it a try. Well, well, the wind pushed the bullet far enough over so it hit the steel frame of the target holder, and knocked the whole shebang over.
Photos show the bullet after hitting steel @ 300 yard.
Then i drove back to where i had been shooting before, and shot twice at 100 yard.
A move was made to 200 yard, and 3 shots taken. The breeze was left to right.
When the rifle was cleaned for the initial shooting a couple day ago, i didn't replace the new breech plug. The new plug was exchanged with one that had worn at both ends. The worn flash hole was replaced with a stainless vent liner, and the flame cut primer seat was cut deeper, and now an o-ring is used.
The last photo shows the rifle with a 1X scope just now mounted. And now you know what the next task will be.
#3
Fork Horn
Join Date: Aug 2008
Posts: 330
Got to love those Omegas. Mine really likes 110 gr of BH209, Winchester 209 primers and about anything I stuff down the barrel. I've been going to put a thumbhole laminate stock on it and top it with a 4x12 or 4x14 scope just to do some long distance shooting. Now it looks like I'll have to get this done a little sonner. Thanks and great shooting.
#5
Spike
Join Date: Aug 2012
Location: Amarillo, Texas
Posts: 2
I have a 50 Cal Omega that shoots Buffalo Bullets "old" 375 Gr Boat Tail Spitzer/Sabot bullet really well, under 1/2 inch at 100 yards, but I am nearly out of them. I need some help locating some of them that I could buy or trade for.
#6
Spike
Join Date: Aug 2012
Location: Amarillo, Texas
Posts: 2
I found that 54 cal pellets will fit and work fine in 50 cal rifles. The benefit to me was that they come in 60 gr pellets. when I loaded 3x50 grain pellets my accuracy suffered to the point that the increase in velocity was useless. The increase from 2x60 grain pellets was substantial with virtually no increase in group size.
#8
Nontypical Buck
Thread Starter
Join Date: Aug 2008
Location: Rapid City, South Dakota
Posts: 3,732
Seems, i do recall you purchasing the exact same rifle i did. You sold your Mountaineer to do so i think. My clearance Omega does shoot straighter than my Mountaineer, and it is shorter, lighter, and not as pretty.